An Integrated Publishing, Inc. Site

An Integrated Publishing Website

Electrical Electronic Equipment Components - FSC 59GP

EIA359 - Color Identification And Coding, Eia Standard Colors For

The colors defined in this standard are intended to be applied to the marking of electronic components such as resistor, capacitors, and wires in a manner described in the EIA Standards for these components.

EIA557.1 - Components, Passive, Guidance For The Selection Of Critical Manufacturing Operations For Use In Implementing An Spc System For

This guidance is applicable to general electronic components with emphasis on the specific parts shown in Appendix A.

EIA584 - Zero Acceptance Number Sampling Procedures And Tables For Inspection By Attributes For A Continuous Manufacturing Process

Conventional attribute sampling plans based upon nonzero acceptance numbers are no longer desirable.

EIA585 - Zero Acceptance Number Sampling Procedures And Tables For Inspection By Attributes Of Isolated Lots

Conventional attribute sampling plans based upon acceptance numbers that permit acceptance of a lot when some allowable number of nonconformances are encountered during inspection are no longer desirable.

EIA-RS359 - Colors For Color Identification And Coding Eia Standard

IEEE-C37.30 - Air Switches, High-Voltage

J-STD-002 - Solderability Tests For Component Leads, Terminations, Lugs, Terminals And Wire

This standard prescribes the recommended test methods, defect definitions, acceptance criteria, and illustrations for assessing the solderability of electronic component leads, terminators, solid wire, stranded wire, lugs, and tabs.

MIL-C-21743 - Composite Electric Components General Specification

MIL-C-28790 - Circulators, Radio Frequency, General Specification For (S/S By Mil-Dtl-28791)

This specification covers the general requirements for circulators, coaxial, wave-guide, and strip-line radio frequency for use in armed-service radar and radio application.

MIL-E-24762 - Enclosures For Electronic Equipment, Survivable, Naval Shipboard Use

This specification establishes the design, development performance, and test requirements for survivable electronic enclosures for shipboard-survivable electronic systems and equipment. Only one classification of enclosure is covered by this specification.

MIL-E-5135 - Electronic-Standard-Items; Part, Material And Process

MIL-F-28821 - Filter Unit, Notch

This specification establishes the technical requirements for High Frequency (HF) dual-channel Notch Filter Unit. This unit shall provide special purpose shipboard receivers with protection from overload by local onboard transmitters over the frequency range of 2.0 to 24.0 Megahertz (MHz).

MIL-F-28861/16 - Filters And Capacitors, Radio Frequency/Electromagnetic Interference Suppression, Hermetically Sealed, Style Fs66

MIL-F-28861/17 - Filters And Capacitors, Radio Frequency/Electromagnetic Interference Suppression, Hermetically Sealed, Style Fs67

MIL-G-16560 - Gas Discharges In Tr And Attenuator Tubes, Study Of

MIL-HDBK-279 - Total Dose Hardness Assurance Guideline For Semiconductor Device And Microcircuit (S/S By Mil-Hdbk-814)

The scope of this document is limited to total-dose radiation effects on electronic piece parts. It does not address overall system hardness assurance activities. However, occasionally, specific system requirements may be briefly addressed when it facilitates the discussion.

MIL-HDBK-280 - Neutron Hardness Assurance Guidelines For Semiconductor Devices And Microcircuits (S/S By Mil-Hdbk-814)

Hardness assurance (HA) for electronic piece parts is the application of methods and procedures during the procurement of an electronic piece part to ensure that the radiation response of the purchased part is within known and acceptable limits.

MIL-HDBK-600 - Guidelines For Identification, Marking, Labeling, Storage, And Transportation Of Radioactive Commodities (See Notice 1 For Replacement Information

This handbook provides general information for shippers, carriers, and handlers of radioactive commodities for use and storage, and for shipment by any mode of transportation, to insure that such materials are properly packaged, packed, marked, and labeled, when offered for storage or shipment.

MIL-HDBK-814 - Ionizing Dose And Neutron Hardness Assurance Guidelines For Microcircuits And Semiconductor Devices

Systems that must operate in a radiation environment have to be designed to be survivable (hard) to radiation stress levels specified for them. In addition to design hardening, a Hardness Assurance (HA) program must also be developed during the system design phase for implementation of the production phase. The HA program consists of the production controls and tests which assure that each end product, i.e., delivered system, meets the hardened design specifications and requirements. This handbook is a revision and combination of the earlier MIL-HDBK-279 (see 6.1) and MIL-HDBK-280 (see 6.2) which in turn were the results of earlier work performed under the auspices of the Defense Nuclear Agency ((DNA see 6.3 and 6.4).

MIL-HDBK-815 - Dose-Rate Hardness Assurance Guidelines

The scope of this document is limited to dose-rate radiation effects on semiconductor electronics and is specifically intended to address hardness assurance at the piece-part level. Because the nature of dose-rate effects sometimes requires a close interaction between system hardness assurance and piece-part hardness assurance, some system requirements are also discussed.

MIL-HDBK-816 - Guidelines For Developing Radiation Hardness Assurance Device Specifications

The primary objective of this document is to provide guidelines and easy to follow procedures for the preparation of detailed device specifications for the procurement of microcircuits and semiconductor devices where radiation Hardness Assurance (RHA) is required. The guidelines are applicable to MIL-M-38510, MIL-PRF-38534, MIL-PRF-38535, and MIL-PRF-19500 microcircuit and semiconductor device detailed specifications, Standard Microcircuit Drawings (SMDs) as well as other contractor prepared specifications such as Source Control Drawings (SOCD), Selected Item Drawings (SID), and Specification Control Drawings (SCD). Recommended procedures are provided for characterizing the radiation response of a part and for obtaining post-irradiation post-irradiation end-point limits for qualification and Lot Acceptance Tests (LAT).

MIL-HDBK-817 - System Development Radiation Hardness Assurance

The U.S. Government is developing a large number of complex systems that are required to function during or after exposure to a radiation environment. The need for these systems to accomplish their designated mission regardless of their complexity and the hostile environment that they must withstand dictates that attention be focused on hardening design techniques and hardness assurance methods used during the development and production phases of the system. While Hardness Assurance (HA) procedures are implemented during the production phase, there are HA activities that must occur during the earlier design and development phases.

MIL-HDBK-978 - Nasa Parts Application Handbook With Volumes 1-5

MIL-HDBK-979 - Nasa Standard Parts, Data Sheets For

MIL-L-8050 - Lobe Switch, Antenna Sa-314( )-Apx

MIL-N-87144 - Network, Fixed Film Resistors And Ceramic Capacitors, General Specification For (S/S By Mil-R-83401)

MIL-P-38106 - Test Carrier For Electronic Component Parts, General Specification For

MIL-PRF-15733/27 - Filters And Capacitors, Radio Frequency Interference, Hermetically Sealed, Style Fl15

MIL-PRF-15733/34 - Filters And Capacitors, Radio Frequency Interference, Hermetically Sealed, Style Fl90

MIL-PRF-15733/49 - Filters And Capacitors, Radio Frequency Interference, Hermetically Sealed, Style Fl93

MIL-PRF-15733/58 - Filters And Capacitors, Radio Frequency Interference, Hermetically Sealed, Style Fl63

MIL-PRF-15733 - Filters And Capacitors, Radio Frequency Interference, General Specification For

This specification covers the general requirements for low-pass filters and capacitors used to suppress radio frequency/electromagnetic interference. Filters furnished to the requirements of this specification contain shunting capacitors and series inductors (FSC 5915). Capacitors furnished to the requirements of this specification

MIL-PRF-28861/10 - Filters And Capacitors, Radio Frequency/Electromagnetic Interference Suppression, Hermetically Sealed, Style Fs64

MIL-PRF-28861/12 - Filters, And Capacitors, Radio Frequency/Electromagnetic Interference, Suppression, Hermetically Sealed On One End Only, Style Fs70

MIL-PRF-28861/13 - Filters And Capacitors, Radio Frequency/Electromagnetic Interference Suppression, Hermetically Sealed On One End Only, Style Fs72

MIL-PRF-28861/14 - Filters And Capacitors, Radio Frequency/Electromagnetic Interference Suppression, Hermetically Sealed On One End Only, Style Fs73

MIL-PRF-28861/15 - Filters And Capacitors, Radio Frequency/Electromagnetic Interference Suppression, Hermetically Sealed On One End Only, Style Fs74

MIL-PRF-28861/18 - Filters And Capacitors, Radio Frequency/Electromagnetic Interference Suppression, Hermetically Sealed, Style Fs68

MIL-PRF-28861/1 - Filters And Capacitors, Radio Frequency/Electromagnetic Interference Suppression, Hermetically Sealed, Styles Fs10 And Fs11

MIL-PRF-28861/6 - Filters And Capacitors, Radio Frequency/Electromagnetic Interference, Suppression, Nonhermetically Sealed, Style Fs60

MIL-PRF-28861/7 - Filters And Capacitors, Radio Frequency/Electromagnetic Interference Suppression, Nonhermetically Sealed, Style Fs61

MIL-PRF-28861/8 - Filters And Capacitors, Radio Frequency/Electromagnetic Interference Suppression, Hermetically Sealed, Style Fs62

MIL-PRF-28861/9 - Filters And Capacitors, Radio Frequency/Electromagnetic Interference Suppression, Nonhermetically Sealed, Style Fs63

MIL-PRF-28861 - Filters And Capacitors, Radio Frequency/Electromagnetic Interference Suppression, General Specification For

This specification covers the general requirements for low-pass filter and capacitors used to suppress radio frequency/electromagnetic interference. Filters furnished to the requirements of this specification contain shunting ceramic discoidal capacitors and series inductors (FSC 5915). Capacitors furnished to the requirements of this specification contain shunting ceramic discoidal capacitors (FSC 5910). For the purposes of this specification, feed-through capacitor types (C circuit configuration) are referred to herein as a filter. Passband power may be alternating current (ac) or direct current (dc) and the filters used primarily in the reduction of broadband radio frequency interference. This specification provides for two levels of product assurance requirements. Filters covered by this specification are capable of operation over the temperature range of -55 degrees C to +125 degrees C.

MIL-PRF-83401 - Resistor Networks, Fixed, Film, And Capacitor-Resistor Networks, Ceramic Capacitor And Fixed, Film, Resistors, General Specification For

This specification covers the general requirements for hermetically sealed (see 3.10) and nonhermetically sealed (see 3.10.1) networks. These networks consist entirely of fixed, film resistors, or fixed, film resistors and ceramic capacitors. They are primary intended for use in electronic circuits. This specification has two product levels, a high reliability, 100 percent burn-in screened "M" part number level and nonburn-in screened (without the mandatory conformance inspection) part number level "C" (see 1.2.1). Designers are CAUTIONED on using these resistors in high power pulses applications (see 6.8).

MIL-R-19610 - Reliability Of Production Electronic Equipment General Specification For

MIL-R-22256 - Relialibility Requirements For Design Of Electronic Equipment Or Systems (S/S By Mil-Std-785)

MIL-R-38100 - Reliability And Quality Assurance Requirements For Established Reliability Parts, General Specification For

MIL-STD-1285 - Marking Of Electrical And Electronic Parts

This standard establishes requirements for the physical marking of electrical and electronic parts. This standard should be implemented by incorporating suitable requirements directly in acquisition documents.

MIL-STD-1285-SUP-2 - Marking of Electrical and Electronic Parts

MIL-STD-1395 - Filters And Networks Selection And Use Of

This standard consists of the following: a. Selected standard filter and network styles and types, detailed by sections, chosen jointly by the Department of the Army, the Navy and the Air Force for use in new design and manufacture of military equipment under the jurisdiction of the Departments. b. Guides for the choice and use of filters and networks for new military equipment.

MIL-STD-1549 - Common Termination System For Electrical And Electronic Parts

This standard establishes the design, technical, and performance requirements necessary for implementing the Common Termination System (CTS) on any electrical or electronic part or terminal junction system (modules and splices).

MIL-STD-1580 - Destructive Physical Analysis For Electronic, Electromagnetic, And Electromechanical Parts

This standard describes the general requirements for performance of destructive physical analysis (DPA) on samples of parts. In addition to the requirements for the analysis procedures, the general criteria for interpreting results, such as for the acceptance or rejection of associated production lots, is included for typical electronic, electromagnetic, and electromechanical parts.

MIL-STD-1631 - Procedure For Selection Of Electronic And Electrical Parts And Materials During Design Of Military Items (See Mil-Std 965)

MIL-STD-174 - Color For Coding Electronic Parts (S/S By Mil-Std-1285)

MIL-STD-202 - Electronic And Electrical Component Parts

This standard establishes uniform methods for testing electronic and electrical component parts, including basic environmental tests to determine resistance to deleterious effects of natural elements and conditions surrounding military operations, and physical and electrical tests. For the purpose of this standard, the term "component parts" includes such items as capacitors, resistors, switches, relays, transformers, inductors, and others. This standard is intended to apply only to small component parts, weighing up to 300 pounds or having a root mean square test voltage up to 50,000 volts unless otherwise specifically invoked.

MIL-STD-242-10 - Wire And Cable (Part 10)

This standard established the requirements for the selection of wire and cable used in the design and manufacture of Navy equipment.

MIL-STD-242-12 - Electronic Equipment Parts Selected Standards Hardware & Insulators Part 12

This standard establishes the requirements for the selection of hardware and in-sulators used in the design and manufacture of Navy equipment.

MIL-STD-242-1 - Electronic Equipment Parts Selected Standards Synchros, Blowers, And Acoustical Parts (S/S By Mil-Std-710, Mil-B-23071, Mil-Std-2115)

This section covers SYNCHROS, 60 and 400 Hz. These SYNCHROS shall be used in conjunction with MIL-S-81963.

MIL-STD-242-2 - Electronic Equipment Parts Selected Standards Crystals, Delay Lines, Coils, And Transformers

MIL-STD-242-3 - Electronic Equipment Parts Selected Standards Resistors (S/S By Mil-Std-199)

This standard establishes the requirements for the selection of resistors used in the design and manufacture of Navy equipment.

MIL-STD-242-4 - Electronic Equipment Parts, Selected Standards Capacitors (S/S By Mil-Std-198)

This standard establishes the requirements for the selection of capacitors used in the design and manufacture of Navy equipment.

MIL-STD-242-5 - Electronic Equipment Parts, Selected Standards, Microcircuits & Semiconductors (S/S By Mil-Std-1562 & Mil-Std-701)

This standard establishes the requirements for the selection of microcircuits and semiconductors used in the design and manufacture of Navy equipment.

MIL-STD-242-7 - Electronic Equipment Parts, Selected Standards Switches (S/S By Mil-Std-1132)

MIL-STD-242-8 - Electronic Equipment Parts Selected Standards Connectors And Sockets - Part 8

This standard establishes the requirements for the selection of connectors used in the design and manufacture of Navy equipment.

MIL-STD-242-9 - Electronic Equipment Parts Selected Standards Circuit Breakers, Fuses, Lamps, And Meters (S/S By Mil-L-3661, Mil-L-6363, Mil-L-15098, A-A-50454, A-A-50588, Mil-Std-1279, Mil-M-7793, Mil-Std-1498, And Mil-Std-1360)

The purpose of this standard is to control and minimize the variety of circuit breakers, fuses, lamps, and meters in Navy equipment in order to facilitate effective logistic support, improve quality and reduce cost.

MIL-STD-242 - Electronic Equipment Parts Selected Standards Crystals, Delay Lines, Coils, And Transformers (S/S By Mil-Std-683, Mil-Std-1837, Mil-Std-1286)

This standard establishes the requirements for the selection of relays used in the design manufacture of Navy equipment.

MIL-STD-439 - Electronic Circuits

MIL-STD-441 - Reliability Of Military Electronic Equipment (S/S By Mil-Std-785)

MIL-STD-701 - Lists Of Standard Semiconductor Devices (S/S By Mil-Hdbk-5961)

This standard establishes the requirement for the selection of semiconductor devices used in the design and manufacture of military equipment.

MIL-STD-749 - Preparation And Submission Of Data For Approval Of Nonstandard Parts (See Mil-Std-965)

MIL-STD-790 - Established Reliability And High Reliability Qualified Products List (Qpl) Systems For Electrical, Electronic, And Fiber Optic Parts Specifications

This standard is for direct reference in established reliability and high reliability electrical, electronic, and fiber optic parts specifications and establishes the criteria for a manufacturer?╞s qualified product system.

MIL-STD-790-SUP - Established Reliability and High Reliability Qualified Products List (QPL) Systems for Electrical, Electronic, and Fiber Optic Parts Specifications

MIL-STD-975 - Nasa Standard Electrical, Electronic, And Electromechanical (Eee) Parts List

This standard provides a means of selecting, procuring and applying Electrical, Electronic, and Electromechanical (EEE) Parts for use in flight and mission-essential ground support equipment.

MIL-T-152 - Treatment, Moisture And Fungus-Resistant, Of Communications, Electronic, And Associated Electrical Equipment

This specification covers the requirements for the application of moisture - and fungus-resistant varnish to those assembled communications, electronic, and associated electrical equipments and certain of their component subassemblies, individual parts, solder connections,and fungus-nutrient materials which are not moisture resistant or whose moisture- and fungus-resistant properties cannot be predicted.

MIL-T-4734 - Transit Cases, Combination Cases And Spare Parts Cases For Ground Electronic Equipment (Usaf) (Requirements For) (S/S By Mil-C-4150 & Mil-C-5584)

This specification covers the requirements for two types of transit cases designated Transit Cases, Combination Cases and Spare Parts Cases, Type I or Type II hereinafter referred to as the "type number" or "transit case"when referred to collectively.

MS27311 - Test Carrier, Stick Type, Three Terminal Device

MS27312 - Test Carrier, Stick Type, Two-Terminal Device

MS27313 - Test Carrier, Wafer Type Micro-Electronic Functional Device, Fourteen Terminal

MS27314 - Test Carrier, Wafer Type, Three Terminal, .215 Diameter

MS27315 - Test Carrier, Wafer Type Three Terminal, .760 Diameter

MS27316 - Base,Test Carrier Assembly, Wafer Type

MS27317 - Test Carrier Liner, Two Terminal Device

MS27318 - Test Carrier Liner, Three Terminal Device

MS27319 - Component Release Tool And Liner Removal Tool, Component Test Carrier, Two Terminal Device

MS27320 - Component Release Tool And Liner Removal Tool, Component Test Carrier, Three Terminal Device

MS27321 - Tray, Component Carrier Stick

MS27322 - Tray, Transistor Carrier Stick

MS27323 - Insert Tray, Wafer

MS27324 - Spacer, Carrier Stick

MS27325 - Window, Carrier Stick

MS27326 - Lid, Carrier Stick

MS27327 - Cover, Carrier Stick

MS27358 - Spacer, Test Carrier Assembly, Matrix Type

MS27359 - Test Carrier Assembly, Matrix Type

MS27360 - Test Carrier Assembly, Matrix Type

MS27361 - Test Carrier Assembly, Matrix Type

NFPA70 - Equipment, Electrical, Maintenance

QPL-15733-113 - Filters And Capacitors, Radio Frequency Interference, General Specification For (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)

QPL-28861-41 - Filters And Capacitors, Radio Frequency/Electromagnetic Interference Suppression, General Specification For (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)

QPL-83401-87 - Resistor Networks, Fixed, Film, And Capacitor-Resistor Networks, Ceramic Capacitor And Fixed Resistors, General Specification For (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)

UL508 - Industrial Control Equipment

These requirements cover industrial control devices, and devices accessory thereto, for starting, stopping, regulating, controlling, or protecting electric motors.

ng, 37.5 Kw, Type Mc-1

MIL-R-26627 - Regulator, Airport Lighting Rgu-3/F, Rgu-4/F, Rgu-S/F, And Rgu-11/F

MIL-R-2729 - Regulator-Exciter Systems, Voltage, A.C. General, Naval Shipboard Use

This specification covers high impact (HI) shockproof alternating current (ac) generator voltage regulator-exciter systems for use on Naval surface ships and submarines.

MIL-R-4707 - Regulator, Constant Current, Taxiway Lighting, Type M-1

This specification covers one type of taxiway lighting constant current regulator, designated Type M-1.

MIL-R-52939 - Regulator, Current, Runway Lighting, 120 Volt, 2 1/4 Kw, Ac

MIL-R-55223 - Regulator, Voltage Cn-514( )/Grc

MIL-R-55477 - Regulator, Voltage Cn-1130( )/G

MIL-R-6339 - Regulator, Voltage, Type L-4

MIL-R-6365 - Regulator, Constant Current, Runway Lighting, 240V Primary 4Kw, Type C-1

MIL-R-6402 - Regulator, Current, Constant, Taxiway Lighting, Type M-2

MIL-R-7643 - Regulator, Current, Runway Lighting 120V 2-1/4 Kw Ac Type C-2

MIL-R-9681 - Regulator, Voltage Cn&345()-Gps And Cabinet, Electrical Equipment Cy&1876()-Gps

MIL-S-10321 - Switching-Group, Power, Electrical, Medium-Voltage.

MIL-S-12514 - Starter, Motor, Across-The-Line And Reduced Voltage Types, Ac Induction, 3/4 To 100 Hp Manual And Electric

MIL-S-12662 - Switchboard, Interior Communication (Control Switchboard Sb&100)( -Mtc) (Supersedes 71&3411)

MIL-S-15001 - Switchboard, Interior Communication, Naval Shipboard (S/S By Mil-S-17000)

MIL-S-15722 - Switchgear Groups, Generator Control And Distribution For Asr Vessels

MIL-S-16465 - Switchboard, Paralleling, 120 Volt, A. C. Generator, 400 Cycle, 3 Phase, Submarine (Use Mil-S-16036)

MIL-S-18475 - Switchboard, Power, Naval Surface Ship Propulsion Control

MIL-S-18846 - Switchboards, Power (Control Cubicle), Submarine Ss 580 Propulsion Control

MIL-S-19217 - Switchboards, Power (Control Cubicle), Submarine Ss 580 Propulsion Control

MIL-S-19733 - Switchboards, Power (Control Cubicle), Submarine Propulsion

MIL-S-24158 - Static Adjustable Speed Control System For A.C. Induction Motor (Adjustable Frequency Type) Naval Shipboard

MIL-S-24188 - Synchronizing Control Equipment, 60 Cycles, 450 Volts, Naval Shipboard

This specification covers general requirements for generator synchronizing monitor protective equipment for use with generator sets rated up to 2500 kilowatts (kw), 450 volts, 3 phase, 60 cycle.

MIL-S-24370 - Solenoids, Electrical (Naval Shipboard) (S/S By Mil-S-4040)

MIL-S-24561 - Sensing And Signaling Device, Current-Time (Cts) (Naval Shipboard Use)

This specification covers a current-time sensing and signaling device (CTS) and a test act for such device for use on Naval ships.

MIL-S-28667 - Switchgear, Power Outdoor Type, Fuse & Switch Metal Enclosed, Skid Mounted, 2400/4160 Volts, Ac (S/S By Ieee-C37.20)

MIL-T-18071 - Taping Machine, Armature Coil, Power Driven, Shipboard Use

MIL-T-4977 - Panel, Power Distribution, Airport Approach And Runway Lighting, Type Mc-1 (S/S By Mil-P-8945)

MIL-V-10537 - Voltage Regulator Group, For Multiplex Projectors

MIL-V-17958 - Voltage Regulator Mark 1 Mod 0

MS18071 - Regulator Voltage, Direct Current Generator, 28 Volts, Solid State

MS21961 - Panel Relay, Pilot, Enclosed, Airport Lighting (Types I And Ii)

MS23001 - Cubicle, Power Distribution, Automatic Transfer, Airfield Lighting

MS24437 - Wiring Diagram & 115-200V, 1 Phase Variable Frequency System, Manual Bus Selection, Schematic (Supersedes Usaf Dwg 52D6872)

MS24438 - Wiring Diagram-115/200V, 3 Phase Variable Frequency System, Manual Bus Selection, Schematic

MS24441 - Wiring Diagram External A.C. Power Receptacle, Schematic

MS24442 - Wiring Diagram - External Power Receptacle, 28 Volt D.C., Common Bus System

MS24454 - Wiring Diagram & Power System Bus, Schematic (Supersedes Usaf Dwg 49B7567)

MS24460 - Wiring & Diagram & Power Supply, 115 Volts 400 Cycles, 3 Phase 100 Va (Supersedes Usaf Dwg 51B6880)

MS25001 - Bracket, Pilot, Voltage Regulator Base (See Rev. C For Additional Information)

MS25220 - Regulator-Voltage, 120 Degree Centigrade Class, Direct Current Generator 28 Volts

MS25263 - Supervisory Panel, A. C., Aircraft Single Generator, Class C

NEMA-PB2.1 - Switchboards 600 Volts Or Less, Deadfront Distribution, Proper Handling, Installation, Operation, And Maintenance Of, General Instructions For

NEMA-SG2 - Fuse, High Voltage, Standard For

QPL-16392-41 - Brakes, Magnet, Naval Shipboard

QPL-17706 - Regulator Set, Voltage, Dc Generator (Naval Shipboard Use)

QPL-17773-55 - Switches, Bus Transfer, Electric Power, Automatic And Manual (Metric)(Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)

QPL-2174-13 - Controller, Direct Current, Naval Shipboard (Use Qpl 2212)

QPL-22109-8 - Contactor And Controller, Electrical, Engine Starting, (Naval Shipboard)

QPL-2212-53 - Contactors And Controllers, Electric Motor Ac Or Dc, And Associated Switching Devices (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)

QPL-23098-12 - Regulators, Line Voltage, Single Phase, 400 Hertz A.C. Naval Shipboard(Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)

QPL-23761-17 - Regulators, Voltage, And Control Panels, Aircraft Direct Current Generator, General Specification For (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)

QPL-24021-18 - Electric Power Monitors, External, Aircraft (Replaced By The Qualified Products Database (Qpd) See Notice 1 For Additional Information)

QPL-25077-1 - Regulator, Voltage, Aircraft Generator, 115V Ac, Single Phase, 8 Kva, Type Ma-3

QPL-26627-6 - Regulator, Airport Lighting Rgu-3/F, Rgu-4/F, Rgu-5/F, And Rgu-11/F

QPL-5746-2 - Amplifier, Single Channel, Cylinder Head Temperature, Type A-10

QPL-81305-5 - Power, Distribution Panel, Alternating Current, F-4 Aircraft, Specification

QPL-8509-1 - Voltage Stabilizers, Alternating Current, Aircraft, General Specification For

QPL-9450-1 - Panel, Control, Generator, Type B-3

UL869 - Equipment Service Standard For

These requirements cover service equipment rated 600 volts or less intended to be employed in accordance with the National Electrical Code, ANSI/NFPA 70.

UL869 - Service Equipment, Reference Standard For

This standard provides specific service equipment requirements that are intended to be supplemented by requirements for other types of equipmnet (such as panelboards, switchboards, and the like) that may be used a s service equipment.

UL891 - Switchboards, Dead-Front

These requirements cover dead-front switchboard sectons, interiors, and enclosures, rated 600 volts maximum, and intended to be employed as dead-front switchboards in accordance with the National Electrical Code, NFPA 70.